SKU: Damping Turing Tool Holder (No.1)
Categories: Boring Bars, TURNING TOOLS
Boring Bars, TURNING TOOLS
Damping Turing Tool Holder (No.1)
Availability:
200 in stock
- This is a tool that can reduce or even eliminate vibration.
Based on 0 reviews
0.0 overall
0
0
0
0
0
Be the first to review “Damping Turing Tool Holder (No.1)” Cancel reply
You may also like…
Related products
-
TURNING TOOLS, Turning Inserts
GENERAL TURNING Turning Inserts(Negative) DNMG Rhombic 55° with Hole
0 out of 5(0)- GF for finishing of general steel and alloy steel.
- Sharp tool nose and strong cutting edge.
- Good chip control under small cutting depth.
- QF for finishing of general steel and alloy steel.
- Curved edge,sharp cutting edge, good chip control and fine surface finish due to curved edge.
- SF for stainless steel and Heat
- Sharp edge due to results in low cutting forces particularly for thin wall structures and extended shafts.
- GM for semi-finishing of general steel and alloy steel.
- Strong flat cutting edge.
SKU: Turning Inserts(Negative) DNMG Rhombic 55° with Hole 1$28.00 -
TURNING TOOLS, Turning Inserts
GENERAL TURNING Turning Inserts(Negative) WNMG Trigon60°,with Hole
0 out of 5(0)- GF for finishing of general steel and alloy steel.
- Sharp tool nose and strong cutting edge.
- Good chip control under small cutting depth.
- QF for finishing of general steel and alloy steel.
- Curved edge,sharp cutting edge, good chip control and fine surface finish due to curved edge.
- SF for stainless steel and Heat
- Sharp edge due to results in low cutting forces particularly for thin wall structures and extended shafts.
- LF for stainless steel finishing to semi-finishing.
- Small blade width + large rake angle, increase the strength of the blade.
- Curved blade design, stable cutting flow direction control.
- GM for semi-finishing of general steel and alloy steel.
- Strong flat cutting edge.
- QM for semi-finishing of general steel and alloy steel.
- Gradient and waved hump wide applicable geometry range.
SKU: Turning Inserts(Negative) WNMG Trigon60°,with Hole 1$20.00 -
TURNING TOOLS, Turning Inserts
GENERAL TURNING Turning Inserts(Negative) TNMG Triangle 60°,with Hole
0 out of 5(0)- GM for semi-finishing of general steel and alloy steel.
- Strong flat cutting edge.
- QM for semi-finishing of general steel and alloy steel.
- Gradient and waved hump wide applicable geometry range.
- TP For semi-finish machining of ordinary steel, alloy steel and cast iron.
- Double front angle, large blade width design, enhance the strength of the blade.
- Overall pattern design, stable and reliable installation.
- Arrow-shaped chipbreaker improves chipbreaking performance at large cutting depths.
- TS for semi-finishing of general steel and alloy steel.
- Big rake,smooth chip evacuation.
- Variable groove depth design, with super chip removal.
SKU: Turning Inserts(Negative) TNGG/TNMG Triangle 60°,with Hole 2$18.00$20.00 -
TURNING TOOLS, Turning Inserts
GENERAL TURNING Turning Inserts(Negative) SNMG Square 90°,with Hole
0 out of 5(0)- QM for semi-finishing of general steel and alloy steel.
- Gradient and waved hump wide applicable geometry range.
- TP For semi-finish machining of ordinary steel, alloy steel and cast iron.
- Double front angle, large blade width design, enhance the strength of the blade.
- Overall pattern design, stable and reliable installation.
- Arrow-shaped chipbreaker improves chipbreaking performance at large cutting depths.
- SV for semi-finishing of general steel and alloy steel.
- Throughout groove and wide chip groove make cutting available in unstable working conditions.
- Long chip groove allows high depth of cuts.
- SM for medium cutting of stainless steel and mild steel.
- Sharp cutting edge.
SKU: Turning Inserts(Negative) SNMG Square 90°,with Hole 2$19.00
There are no reviews yet.